Signal SPD
Signal surge protective device (SPD) is actually a signal lightning arrester, which is installed in series in the signal transmission line, usually at the front end of the equipment, to protect the subsequent equipment-all kinds of signal lines and equipment, and prevent lightning waves from influencing the signal line and damaging the equipment.
Its main functions are:
Limit the transient overvoltage caused by the induced lightning in the signal line. According to surveys, more than 80% of lightning strikes in electronic systems are caused by induced lightning. Therefore, the wide application of microelectronic equipment in modern society should strengthen the lightning protection of electronic systems and install suitable signal surge protector .
Limit the surge caused by the start and stop of the electronic system. In addition to the lightning induction caused by the surge in the signal line, the most important reason is the start and stop of the electronic equipment. This kind of surge is widespread. The installation of a suitable signal surge protection device on the line can effectively suppress the surge caused by the operation of the electronic system, and can effectively reduce the deterioration and failure of electronic sensitive components, and ensure the signal line The stability, prolong the service life of electronic equipment.Signal smart surge protectors can be divided into network signal surge protectors, monitoring signal surge protectors, control signal surge protectors, video signal surge protectors, telephone signal surge protectors according to different types of protected lines, Explosion-proof signal surge protectors,s and many other types, each type has many models, parameters and different appearances.
RJ45 SPD 10/100/1000Mbps network signal surge arrester ethernet surge protection device
Data line protector series are mainly used in TCP/IP communication networks to protect electrical and electronic equipment's signal line from the impact of lightning electromagnetic pulse, induced over-voltage, transient operation, and resonance overvoltage.Signal SPD for Audio Surge Protector
With a standard RJ11 interface, The audio signal lightning protection device is suitable for audio signal lightning protection of 1 to 4 pairs of dedicated communication lines and protection of trunk lines and internal lines of program-controlled exchanges.
SPD for Video Signal System
Come With BNC interface, video signal lightning protection device is suitable for monitoring systems and video-on-demand equivalents Axis communication equipment.
Industrial Control Line AI/AO Analog signal RS485 Protector
The control signal lightning protection device is designed to protect the control line system to protect the electrical and electronic equipment's signal line from the impact of the lightning electromagnetic pulse.
Network SPD for Ethernet Power System
The POE Ethernet series lightning protection device is a lightning protection device developed for POE network power supply equipment in accordance with the standard requirements of IEC61643-21, EN61643-11: 2012, YD5075-98, and IEEE802.3AT.
SPD for Serial Signal System
The serial port signal lightning protection device is designed for communication network line not to be spoiled by lightning over-voltage, induce a voltage, and static discharge.
2 in 1 SPD for CCTV2 in 1 SPD for CCTV
2 in 1 monitor lightning arrester (power and network/ power and video/ power and control), is designed for a digital camera to protect the camera power and data line/power line/video line from the impulse of lightning electromagnetic pulse, induced over-voltage, operating over-voltage.
3 in 1 SPD for CCTV3 in 1 SPD for CCTV
3 in 1 monitoring surge protector is designed to protect the analog monitoring equipment ( power, data, control, video) from the damage of lightning electromagnetic pulse, induced over-voltage, operating over-voltage.
Explosion-Proof Signal Lightning Surge ProtectorExplosion-Proof Signal Lightning Surge Protector
D24(48)Y2/3/4-T provides complete protection for on-site2/3/ 4-wire instruments from damage caused by lightning induced voltage, power interference, electrostatic discharge, etc. The lightning protection device is encapsulated in a 316 stainless steel casing, and can provide 1/2” NPT, M20*1.5, PG13.5, G1/2 and other threaded inlet interfaces.
As a surge protector supplier, we will do our best to meet all the needs of customers.
Contact : win Tech, 0755 86215101
Good deal: buying from seller
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of Signal SPD Search in a category : Raw materials Search in a category : signal |
Friday, April 05, 2013
Quantity : 250 comman - Price : 0,60 €
Anti-glare (matte), hard-coated, dirt-repellent, easy to install and can be removed without leaving any traces The screen protector is designed for application on electronic screens and offers reliable protection against scratches and dirt. The film surface is dull and to mitigate...
QUAD LOGISTICA S.L
- 29010 - MALAGA
- +34 9 12 69 23 06
Friday, September 09, 2016
Quantity : 400 - Price : 8,00 €
Déstokage 400 smoke detectors EI ELECTRONICS EI650 manufactured in Europe with an autonomous lithium battery in until 2026 (20 cartons of 20 detectors with wall mounting screws and operating instructions in French). TECHNICAL CHARACTERISTICS - Test button and break against false...
DOMERCA
- 69100 - VILLEURBANNE
- 06 25 41 37 41
Sunday, January 24, 2016
Steel Structure's Characteristics: Standard: GB50661 JGJ81 BS4592 ASM JIS ISO Size: depend on your drawing Material: Q235 Q345 Welded H Beam and Hot Rolled Section Steel Grade: Grade B Material: material: low carbon steel Roofing : single steel sheet ,RW,EPS, PU,XPS,PF Wall panel...
Hunan ADTO Industrial Group Co., Ltd
- adtosteel
- 413000 - Changsha
- +86 0731 85526339