Equipment goods

Z series DC motor

Z Series DC Motor
Power: 55kw - 1600KW
Voltage: Normal 400V, 440V, 660V
Speed: Rated Speed reference
Protection Degree: IP23/IP44
Insulation Class: F
Duty: S1
Package: Export Wooden Package
Payment: 30% in advance, balance by T/T or L/C at sight.
Contact: Kyle Zhang
Mobile/Zalo: 0086-150 2926 8165
Wechat: SIMOKYLE
E-Mail: simo_mingzhang@foxmail.com
Website: www.wangpaimotor.com

Electrical performance

  1. Data listed in the technical data should be employed under the following conditions:

a) Altitude above sea level maximum 1000m.

b) Cooling air temperature maximal 40, Cooling temperature maximal 32.

c) the motor can be installed under foul situation, but the right cooling method of cooling and defend class must be chosen. If the situation is special, need humid tropic, pls negotiable.

d) The motor is suitable for three-phase bridge system smoothing reactor, also can adopt power supply of dc generator.

e) The motor accord with GB755, "the ration and performance of the rotating electrical machinery", IEC60034-1 and JB/T9577-1999 Technical requirements of Z series middle size electro motor.

  1. The standard rated voltage of the electro motor are 440v, 550v, 660v, etc. Voltage of other classes can also be derived according specific situation, but must be negotiated when ordering.
  2. The basic excitation style is separately excited, the excited voltage is 220v, Voltage of other classes can also be derived according specific situation, but must be negotiated when ordering.
  3. Short time overload capacity of motor

Motor can be divided into 2 kinds according to the use.

First kind (A): ordinary industrial DC motor, Second Kind (B): metal rolling mill DC Motor.

a) First kind(A) motor can endure the overload (1 min) according to table 3.

Table 3

基速的百分数 Percentage of basic Speed)

额定电流的百分数(Percentage of rated current

偶尔使用(Seldom using

经常使用(Constantly using)

100

200(180)

175(160)

200

160.0

150

>300

140.0

125

b) First kind (B) motor can endure the overload (1 min) according table 4.

Table 4

基速的百分数 Percentage of basic Speed)

额定电流的百分数(Percentage of rated current

偶尔使用(Seldom using

经常使用(Constantly using)

100

200(180)

175(160)

200

200180

160

>300

175(160)

140

Note: when the basic speed of motor is equal or greater than the fixed number in Table 4, using the number in the bracket.

Table 4.

Center height(mm)

355

400

450

500

560

630

710

Basic Speed(r/min)

1000

900

800

710

630

560

560

c) the short time overload capacity seldom used means happens infrequency or only at the urgency, the motor working exceed the continuous rated overload capacity, we suggest you adjust the instantaneous open/close device of the switch according to the short time overload capacity seldom using.

The short time overload seldom constantly used means it's an part of the normal working period, the motor endure the continuous rated overload capacity again and again. After working at short time overload, it must working light load to make the overload period's overload root-mean-square less than its continuous ration.

d) Second kind DC motor(B) can endure the following continuous load, Working continuous within the rated voltage and rotate speed with 115% rated power overload, the temperature is higher when at this overload, other features maybe different from working at rated condition.

Within the rated voltage and rotate speed, after running at the rated overload, working at the 125% rated power for 2 hours, the temperature rise can not overrun the regulated numerical value other features maybe different from working at the rated condition.

e) Second kind DC Motor(B), at the rated rotate speed, the overload can reach 2.5 times no longer than 15s only used once in a while.

  1. The change rate of current

Under all rotate speed and load, the change rate of current (di/dt) that the motor can endure is 200 times rated current.

  1. Vibration and noise

a) the vibration of the motor accords with GB/T10068 "Measurement evaluation and limits of the vibration severity of rotating electrical machines which the shaft center height is 56mm and above" center standard's regulation.

b) the noise of the motor accords with GB/T10069 "Measurement of airborne emitted by rotating electrical machinery and noise limits".

  1. The efficiencies listed in the data sheet are for rated output, voltage and speed, and include excitation loss.

The choice of motor capacity

  1. First kind (A): ordinary industrial DC motor. The technical data of this kind of motor pls see the technical data table. Customer can decide the capacity, voltage, running speed and the method of cooling of the motor at customer's option.
  2. Second kind (B): Metal rolling mill DC motor. The output power of this kind of motor is about 20% lower than kind (A), the detail numerical value can be negotiated by the user and manufacture.
  3. Exclude the specification of technical data in the table. Manufacturer can derive other specification at the requirement of the customer model explanation.

Motor Structure

1. The methods and protection degree of the motor

a) The method of cooling of the motor is separately-cooled, according to GB/T1993 "Method of cooling of rotating electrical machinery", there are IC06, IC17, IC37, IC86W. Standard entrance of cooling air is at the end of the main transmission(not the commutator side). The protection class of the motor can be divided into IP23 and IP44 according to the GB/T4942.1 and IEC34-5. If the user needs other method of cooling and defend class, it can be negotiated.

b) the relation between the method of cooling and the protection degree of the motor pls see

Table 1.

c) the cooling method, wind pressure, cooling water flux, motor power see: Table 2.

Frame

Built-on blower

air-to-water heat exchanger

cooling wind

Wind pressure (whisht pressure)

motor power

weight

Cooling water flux

motor power

weight

m³/hr

Pa

KW

KG

m³/hr

KW

KG

H500

10000

1900

7.5

300

19

11

900

H560

16500

2250

15.0

400

22

18.5

1100

H710

23500

2400

18.5

600

40

2*11

1600

  1. The installation and the type of motor according to the GB/T997 "the structure and installation type of rotating electrical machinery", have IM1001(Horizontal bottom install, column biaxial) and IM1002 (Horizontal bottom install, column biaxial). If the user needs other kinds of installation structure, it must be negotiated.
  2. The position of terminal box on standard motor is on the right side when seeing from the main drive end. It can also be installed on the left side, but it must be written in the order contract.
  3. The motor using rolling bearing, nonstop adding oil structure.
  4. The motor can be installed the following accessories at the user's option.
  1. temperature detector component can be put into stator winding and bearing room of 2 side, and connect the outlet wire to the terminal box.
  2. The non-drive party of the machine can equipped with tacho-generator, centrifugal starting switch, coder and others which build up the speed meter protecting device.
  3. Heater for preventing condensation can be installed in the motor, but it must be written in the other contact
  1. The air-to water heat exchanger is usually installed on the top of the motor. If the user wants to be installed on the side of the motor, the user must put forward it when ordering and settle the assistant upholder by the user himself.
  2. The cooler equipped with wind pressure switch, temperature controller, heater for preventing condensation and pther protect device.

Notice on order:

  1. The motor type, power, voltage, running speed, excitation type, cooling type, number of output draft, position of outlet box, etc. Must be written when ordering.
  2. Pls give clear indication of the accessory's type, specification and number installed on the motor when ordering.
  3. If the environment of using is special, humid torrid zone type motor is needed pls write "H" after the original type.
  4. If you have some special requirement of the specification and technical requirement which is not listed in the booklet, pls contact us.
Location : 2# Canal Bridge Industry Park, Baoying Country, Jiangsu, China, 225825 Yangzhou,
Contact : Kyle Zhang, 86 29 89373928

Good deal: buying from seller

Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of
Z series DC motor

Search in a category : Equipment goods
Search in a category :
series, motor
Hong Kong 518100 Audio and Video
LED panel light 1200x300mm 52W

Tuesday, December 31, 2013

Quantity : 100 - Price : $60

Features: 1. Thickness 10mm, super slim; 2. Installation Type: Embedded / Suspended 3. Sandblasting bright silver for 10mm thichness series; 4. Imported Korea diffusion plate,transmittance up to 93%; 5. 0.2W 2835 LEDs,high luminous efficacy, Low light degradation. Beam angle≥110,Ra≥80; 6...

Sinpco Optoelectronic Co.Ltd

  • 518100 - Shenzhen
  • 8613530366710
New Design!! MSW-104 Bubble Bath Spa Massager Full Body Mattress Ozone Massage Non-Slip...

Monday, March 07, 2016

Bubble Bath Spa Massager MSW-104 Bubble Bath Spa Massager is a new generation of home spa massager and is optimized for use in bath with the quality of tranquility, relaxing and luxury life. Configuration of MSW-104 is One-Touch Control Panel with Minimal and fashionable design...

LienJie International Ltd.

  • 414 - Taichung City
  • +886 4 23367128
France 13500 Women clothing
435 Party/Coctail Dress

Sunday, February 08, 2015

Quantity : 435 - Price : 25 € /pièce

Lot de 435 Robes de soirées, Magnifiques 25 € TTC pièce, Made in Turkey, Rapport qualité/prix imbattable Référence DSCTK-SH435RDS État Nouveau Vendu par 1 lot de 435 articles, des dizaines de modèles différents Articles neufs, modèles 2014, en grande partie sériés 38 au 44 ou 38 au 48 Prix ...

BOULEVARD MODE

  • 13500 - Martigues
  • +33 6 52 74 64 10