Algomtl
svgfair.com
 
What gule we should use when coat conveyor drum ?
Details
China Equipment goods
Equipment goods

What gule we should use when coat conveyor drum ?

Quantity : 1   Price : USD 1

What gule we should use when coat conveyor drum ?
To do conveyor drum coating,we need two kinds materials , one is drum coating rubber sheet , the other is glue .
Before coating, we must first know the surrounding environments, and then accord to the technique to choose the right conveyor drum coating glue.
so what glue we should use when do drum coating?
In temrs of pulley lagging techinic in China, cold vulcanizing way is not affected by environmental factors. we always use two kinds
drum coating materials-Ramimtech wear-resistant rubber sheet and cold vulcanzing glue sk313 to do fast cold drum coating.
This pulley lagging process can be on-site,surface or under grounding. Be fast and no need remove drum.
Be with features of high bonding strenght , wear-resistant , high tensile strength, and drum can be back to use soon.
After choosing materials for drum cold bonding coating , then we need know how to do.
Drum cold vulanizing coating method is as follow:
1.Clean residue rubber, oil and dirt frist,and grind repeatly on drum surface using L1202 angle grinder,make drum surface rough and have no rust spot,
then grind softly using fiber buffing disc.
2.After grinding ,clear drum surface using cleaning brush,then do deeper clean using cleaning solution SK353,make sure there isn't any residue.
Wait it dry if there is water on drum surface.
3.Brush metal primer SK363 evenly on the cleaned drum surface,and wait it completely dry.
4.Mix and stir cold vulcanizing glue SK313 with hardener according to the proportion 100: 4.
Brush the mixture on conveyor drum surface hard and evenly,and wait it dry. Then brush second coat after the first coat is dry, meanwhile brush one coat on the back of the rubber sheet.
5.When apply rubber sheet on conveyor drum, need roll rubber surface using roller stitcher, and then hit it firmly using rubber mallet, make sure there is no air trapped between
bonding layers.At last,seal rubber sheet joint using Joint filler, Polish and trim drum lagging egde. Drum conveyor can be back to use after glue is dry.
Above is brief introduction of drum cold vucanizng coating.
To coat conveyor drum in cold vulcanizing way,cold vulcanizing glue sk313 is in common use, it is compound of 1kg adhesive and 40g hardener.
It is with high bonding strength, can be cured at room temperature. Mainly used for bond rubber to rubber , rubber to metal , rubber to fabric,and fabric to fabric, and its
bonding strength is not affected by environmental factors.
Location : No.1 Shangdu Road, 450000 Zhengzhou,
Contact : Brant Gao, 86 371 63486729

Good deal: buying from seller

Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of
What gule we should use when coat conveyor drum ?

Search in a category : Equipment goods
Search in a category :
gule, drum, conveyor, coat
Taiwan 330 Audio and Video
Pole Piece (T-Yoke) for Loudspeakers Motor Assembly

Wednesday, October 21, 2020

SHINING JINS ENTERPRISE specializing in manufacturing & designing cold forge Top Plate (Washer) and Pole piece (T-Yoke) for Loud-Speaker and alarms raw driver in Taiwan. We offer a complete range of Top Plate (Washer) and Pole piece (T-Yoke) uses in Home speaker, P.A. Speaker...

Shining Jins Enterprise Co., Ltd.

  • jsicyoke
  • 330 - Taoyuan City
  • +88 6 33 61 06 38
Germany 60386 Electronics / Computers
Clavier et souris sans fil Logitech MK295 noir au détail 920-009794

Thursday, June 16, 2022

Quantity : 100

Logitech MK295 Silent Wireless Combo. Facteur de forme du clavier: Standard. Style de clavier: Droit. Interface de l'appareil: RF sans fil, Disposition des touches du clavier: QWERTZ, Utilisation recommandée: Bureau. Couleur du produit: Noir. Souris incluse Clavier Utilisation recommandée...

MaKant Europe GmbH & Co. KG

  • 60386 - Frankfurt am Main
  • +49 (69) 9 150 750 14
France 518106 B2B Services
Custom Rapid Prototyping CNC Turning Machining Brass Parts

Friday, January 05, 2024

As a material for brass CNC machined parts manufacturing, brass is an alloy of copper and zinc that has an aesthetically pleasing surface and excellent properties such as high strength, high hardness and strong chemical resistance as well as strong wear resistance. It is a relatively...

YS RAPID MANUFACTURING LIMITED

  • ysrapid
  • 518106 - shenzhen
  • 8615817251032
 
Secure payment

Information

Top search