Silicone potting sealant supplier
Before The Curing
| Performance Indicators | A | B |
| Appearance | Gray Fluid | White Fluid |
| Viscosity | 1500~2500(cps) | 1500~2500(cps) |
| A: B | 1: 1 | |
| Mixed Viscosity | 1500~2500(cps) | |
| Operable Time | 30~120(min) (Adjustable) | |
| Curing Time | 3~5(h) | |
After The Curing
| Hardness | 40~50(Shore A) |
| Dielectric Strength | ≥20(kV/mm) |
| Dielectric Constant | 3.12(1.2MHz) |
| Thermal Conductivity | ≥0.6[W/m.k] |
| Volume Resistivity | ≥1.0×1014(Ω·cm) |
| Specific Gravity | 1.56±0.02(g/cm3) |
| Flammability Rating | UL94 V-0 |
•20kg/set(A10kg+B10kg), packaging with bucket.
![]()
1. Features
ZS-GF-5299E is a low viscosity two-component addition cure silicone sealant, that can be cured at room temperature or heat cure, the higher the temperature, the faster the curing. This product does not produce any byproducts in the curing reaction, which can be applied for PC (poly-carbonate), PP, ABS, PVC and other surface of metal. Complied with the ROHS, REACH of EU directive.
2.The Typical Application
Encapsulating and protecting the power module, or other electronic components.
3. Instructions
•Preparing: Stir completely A and B in each container,
•Mixing:A and B should be fully mixed according to the weighting ratio. Add B to A. Stirring(stir the glue dedicated blade) and mixing. Note that: should be mixed thoroughly when mixing the wall rubber of container into the plastic material.
•De-airing: after mixing which should vacuum degassing for 1-3 minutes.
•Potting: The mixture should be poured into the product as soon as possible, in order to avoid thickening and resulting in poor fluidity.
•Curing: Heat curing or at room temperature curing. The higher the temperature, the quicker curing. The temperature is low, the curing time will be extended either. In winter, it will take a long time to cure, so suggest that heating curing. It is cured for 15 minutes at 80 ° C ~ 100 ° C, about 12 hours at room temperature.
4. Storage
•1 year shelf life if stored below 25 ℃, when the product passed its expiration date, it should be confirmed without abnormal phenomenon, then that can be used.
•These products don't belong to dangerous goods, so they can be transported as normal chemicals. But be careful of leakage.
5. Note
•The mixture should be sealed and stored in a dry environment at room temperature, and should be used as soon as possible, to avoid wastage.
•The product don't belong to dangerous goods, but avoid contacting skin and eyes.
•The product is non-toxic, has good physical inertia without stimulation and harm. The product does not contain flammable and explosive ingredients which will not cause fire or explosion without special requirement for transport.
•Stored for a period of time, the plastic may be layered. So please stir well before using, and can't affect its performance.
•The following substances may hinder the curing or cause the phenomenon of not cure, so it is used after simple experiments, and need to clean the site of application if necessary.
A. incompletely cured condensation type silicone rubber.
B. amine (amine) curable epoxy resin.
C. ash welding, solder flux .

Contact : jiang selina, +086 0769 88888312
Good deal: buying from seller
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
|
This page is about importers and exporters of Silicone potting sealant supplier Search in a category : Stock lots Search in a category : potting, sealant, silicone, supplier |
Thursday, June 12, 2025
Quantity : 10000mt/mo - Price : $3000/ton
+255793159550... High quality Copper Wire Scrap 99.9%/Millberry Copper Scrap 99.99% Our company have the high quality and quantity of Copper Wire Scrap 99.9% / Millberry Copper Scrap 99.99%. The Millberry Copper Scrap we offer is widely demanded amongst the clients for its world wide use...
identa
- +255 - DAR ES SALAAM
- +255793159550
Tuesday, April 14, 2026
Our company is specialized in the export of agricultural products, olive oil and seafood products. Our company guarantees quality and price Location : Algerie, 35200 Alger, Contact : Hocine BOULIFA, +213540746881
SARL BM POISSONNERIE
- 35200 - Alger
- +213540746881
Tuesday, April 22, 2025
Quantity : 1 - Price : 7 700,00 €
Purchase New "HP Designjet Z6800 60 inch Photo Production Printer" from Mitraprint is 100% safe, because purchasing products at Mitraprint provides a 100% money back guarantee. Mitraprint Address : Jl. Sungai Mesa No. 36, Kota Banjarmasin, Kalimantan Selatan 70231 Indonesia. For online...
MITRAPRINT
- 70231 - Banjarmasih
- 081226318601




