Pneumatic Terminal Crimping Machine
Pneumatic Terminal Crimping Machine
Cable Hydraulic Crimping Machine BJ-30T
* Force: 20Ton
* Applicable Scope: 1-200mm² wire
* Stroke: 50mm Adjustable
* Power: 220V/110V
* Size: 60*28*60cm
BJ-607E Pneumatic Terminal Crimping Machine
* Crimping range: 10-300mm2
* Air pressure range: 0.5-0.8MPa
* Output: 9.0T
* Overall dimension: 400*200*210mm
* Weight: 10.5kg
BJ-1200 Pneumatic Crimping Machine
* Crimping range: non-insulated terminals≤10mm²
* Pre-insulated terminals: ≤6mm²
* Tube-shaped terminal: ≤25mm²
* Output: 13.5kg
* Pressure range: 0.4-1MPa
BJ-602E Pneumatic Terminal Crimping Machine
* Crimping range: 0.5-16mm²
* Air pressure range: 0.5-0.8Mpa
* Output: 1.8T
* Voltage range: AC 220V
* Weight: 6kg
* Overall dimension: 275*128*145mm
BJ-606E Pneumatic Terminal Crimping Machine
* Range of Application: 6mm(insulated terminal)//35mm2(Furcate terminal)
* Air pressure range: 0.4-1Mpa
* Output force: 13.5KN
* Voltage range: AC 220V
* Weight: 6.5kg
* Overall dimension: 260*120*140mm
BJ-603E Pneumatic Type Terminal Crimping Machine
* Crimping range: Non-insulated terminal 0.5-50mm² ≤
* Air pressure range: 0.6-1Mpa
* Output: 2.5T
* Voltage range: AC 220V
* Weight: 6kg
* Overall dimension: 286*125*165mm
BJ-604E Pneumatic Type Terminal Crimping Machine
* Crimping range: Tube terminal 0.08-120mm²
* Air pressure range: 0.5-0.8Mpa
* Output: 2.5T
* Voltage range: AC 220V
* Weight: 6.5kg
* Overall dimension: 360*125*165mm
Operation steps of terminal machine
1. Turn on the switch of the terminal crimping machine source, and the power indicator lights.
2. Pay attention to whether there is a noticeable difference in the inside and outside of the machine. If there is a suspension, please check whether the maintenance is needed.
3. Choose and install the knife: it is operated by the designated personnel, and it is necessary to perform the manual comparison with the selected blade before loading the knife. It can be operated without error. Knife installation is completed, the manual test must be used. Firstly turn off the terminal mechanical and electrical source, cut touch button, using a dedicated plate loom, master-slave pulley. The terminal machine stamping trip to maximum, for that hand did not move, considering whether stress or other problems, checking the debug to be OK. The lock screws should be checked and confirmed before the operation.
4. Loading: Install the terminals that need to be hit, use the Allen wrench to adjust feed clamp, and the terminal can easily pass, visual feed position whether appropriate, if not, adjust it, using the Allen wrench to loosen feeder lock screw, a screw dynamic adjustment of the level. Until it is in the best status, then lock feeder and lock screw, begin to work.
5. Testing tension: After the machine is OK, try to take waste wire, tensile test, the main reference value to see "the pull test table" for the specific operation method is as follows, press the tension test the zero key to zero. The terminal wire clip will need to be tested. If the test strain is beyond the scope of standards, the mechanics will adjust it again until reaching the standard value.
6. Trial 10 PCS is sent for the first IPQC to be confirmed that the inspection is OK, which can volume production. In the process of production, the operator must self-check whether the terminals having the plastic bags, hanging, etc. are poor, testing a terminal tensile every 1 hour.
7. Tidy up fine products and waste products after production, cleaning up the surrounding environment sanitation of the machine station.
- 11th Floor, Jingzuan Building, NO. 875 Xiaolin Road, Kunshan, Jiangsu, P.R.C.
- Phone: +86-512-57169166
- Fax: +86-512-57799757
- E-Mail: salome@bojin.hk
- Web: http://www.bojin.hk/products/pneumatic-terminal-crimping-machine/
Contact : Lee Salome, 0086 0512 57169166
Good deal: buying from seller
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
|
This page is about importers and exporters of Pneumatic Terminal Crimping Machine Search in a category : Equipment goods Search in a category : machine, crimping, terminal, pneumatic |
Thursday, August 01, 2013
Quantity : moq:1pcs - Price : USD594
Get stunning images with this High-spec Full HD Memory Camcorder, capable of 1920x1080/50P recording and loaded with F1.2 Super Bright & 29.5mm Wide Angle JVC HD GT LENS and Back-illuminated CMOS Sensor. Built-in Wi-Fi allows Live Monitoring via Smartphone, videos and stills to be emailed...
AC Electronic Ltd
- 999077 - HongKong
- +85 2 23 25 18 67
- +86 13501567844
Sunday, August 10, 2014
Quantity : 25 - Price : USD 3500-88888
Краткие сведения Место происхождения: Китай (материк) Фирменное наименование: ен хуа Номер Модели: yhq Условие: Ново использование: ролик мяч пресс машины гарантия: один год гарантии цвет: как запрос клиента сертификации: исо, се, б. в. преимущества: высокая плотность...
Henan Zhengzhou Yonghua Machinery
- olina1
- 450000 - zhengzhou CITY
- +13 6 07 69 93 63
Tuesday, April 03, 2007
CMR SA Contact: M. Mehmet Cecen Address: 7 grande rue luxembourg, l 1661 Luxembourg Hair straightener from the profesional range PROLISS. 100 W / 200°C Temperature regulator all-ceramic plate Minimum order of 300 items Unit tapering rate up to 17 euros net of tax Consult us for...




