Everything else / Bulk

HDI PCB / BLIND&BURIED VIA HOLE PCB / BVH PCB

SPEEDAPCB has been focusing on the production of various PTH (plated through hole PCB), buried via hole PCB and blind via hole PCB, and HDI PCB prototype.

When it comes to blind and buried hole circuit boards, everyone thinks of HDI boards. Generally, there are more blind and buried hole circuit boards used in mobile phones or navigation instruments. Such PCB boards require high technical content and accurate accuracy. Of course, the price is compared with other It is also high for multilayer circuit boards.

HDI high density interconnect pcb : 1 + n + 1, 1 + 1 + n + 1 + 1, 2 + n + 2, 3 + n + 3,

Features of Blind&Buried Via Hole PCB

HDI PCB

Blind Via Hole is the connection between the outermost circuit in the PCB and the adjacent inner layer with a plated hole. Because the opposite side cannot be seen, it is called blind pass. In order to increase the space utilization between the circuit layers of the board, blind holes come in handy. The blind hole is a via hole to the surface of the printed board.

Buried Via Hole, the connection between any circuit layers in the PCB, but there is no conduction with the outer layer, that is, there is no meaning of a via hole extending to the surface of the circuit board.

HDI PCB

The blind holes are located on the top and bottom surfaces of the circuit board and have a certain depth. They are used to connect the surface layer circuits to the inner layer circuits below. The depth of the holes generally has a prescribed ratio (aperture). This manufacturing method requires special attention, and the drilling depth must be just right. Failure to pay attention will cause difficulties in plating inside the hole. Therefore, few factories will adopt this production method. In fact, it is possible to drill the holes of the circuit layers that need to be connected beforehand, and then glue them together, but they need more precise positioning and alignment devices.

HDI PCB

This manufacturing process cannot be achieved by bonding the circuit boards and then drilling. It is necessary to perform the drilling operation at the individual circuit layer, firstly locally bond the inner layer, then perform plating treatment, and finally all the bonding. Because the operation process is more laborious than the original vias and blind holes, the price is also the most expensive. This manufacturing process is usually only used for high-density circuit boards, increasing the space utilization of other circuit layers.

HDI PCB

In the PCB manufacturing process, drilling is very important. The simple understanding of drilling is to drill the required via holes on the copper clad board, which has the function of providing electrical connections and fixing devices. If the operation of the via is caused by incorrect operation, the device cannot be fixed on the circuit board, which will affect the use of the circuit board, and the entire board will be scrapped. Therefore, the process of drilling is very important.

Parameters of Blind&Buried Via Hole PCB

Items

Capability.

Max board size

580X700mm

Boar Material

FR-4,Aluminum, High Tg FR4,CEM3,etc.

Min trace width/ space (inner layer)

4mil/4mil(0.1mm/0.1mm)

Min PAD (inner layer)

5 mil(0.13mm)

Min thickness(inner layer)

4 mil(0.1mm)

Inner copper thickness

0.5~4 oz

Outer copper thickness

0.4~6 oz

Finished board thickness

0.4-3.2 mm

Board thickness tolerance control

±0.10 mm

±0.10 mm

±10%

±10%

±10%

±10%

Inner layer treatment

brown oxidation

Layer count Capability

1-30 LAYER

alignment between ML

±2mil

Drill hole diameter

0.15mm-0.65mm

Aspect ratio of plated hole

10: 01

Hole precision

±2 mil(±0.05mm)

tolerance for Slot

±3 mil(±0.75mm)

Hole diameter tolerance(PTH)

±3 mil(±0.075mm)

Hole diameter tolerance(NPTH)

±1mil(±0.025mm)

Max Aspect Ratio for PTH

8: 01

Hole wall copper thickness

15-50um

Alignment of outer layers

4mil/4mil

Min trace width/space for outer layer

4mil/4mil

Tolerance of Etching

+/-10%

Thickness of solder mask

on trace

Thickness of solder mask

at trace corner

≥0.2mil(5um)

Hardness of solder mask

On base material

≤+1.2mil

6H

Finished thickness

Alignment of solder mask film

±2mil(+/-50um)

Min width of solder mask bridge

4mil(100um)

Max hole with solder plug

0.5mm

Surface treatment

HAL (Lead or Lead free), immersion Gold, Immersion Nickel, Electric Gold finger, plated Gold, OSP, Immersion Silver.carbon oil,etc.

Max Nickel thickness for Gold finger

280u"(7um)

Max gold thickness for Gold finger

30u"(0.75um)

Nickel thickness in Immersion Gold

120u"/240u"(3um/6um)

Gold thickness in Immersion Gold

2u"/6u"(0.05um/0.15um)

Impedance control and its tolerance

50±10%,75±10%,100±10% 110±10%

Trace Anti-stripped strength

≥61B/in(≥107g/mm)

bow and twist

0.75%

We provide printed circuit board supplies,hdi pcb boardhdi printed circuit boardshdi pcb prototypehdi circuit boardshigh density interconnect pcbhigh density pcbburied via pcb and buried vias pcbRFQ today.

Location : 4F,wangdefu Building,Wanjiali Road,Furong District,Changsha,Hunan, 427000 Changsha,
Contact : Molly Tu speedapcb, +86 0731 15387574935

Good deal: buying from seller

Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of
HDI PCB / BLIND&BURIED VIA HOLE PCB / BVH PCB

Search in a category : Everything else / Bulk
Search in a category :
blind&buried, hole
Thailand 50100 Stock lots
CHAMEX COPY PAPER A4 80GSM/75GSM/70GSM

Tuesday, April 23, 2024

Quantity : 80000 Ream - Price : $0.79/Ream for 8000

SPECIFICATION - Sheet Size: 210mm x 297mm/297mm x 420mm International Paper Standards Size(ISO) A4/A3 - Quality: Imported 100% Virgin Wood Pulp - Whiteness: 102-104%,Natural White - Grading: A - Thickness: 106cm - Capability: High Speed Copying 100ppm, Laser Capable,Inkjet Capable...

NATH LAOH LTD

  • 50100 - Chiang Mai
  • +66 9 95 35 59 56
Vietnam 700000 Furnitures
STAINLESS STEEL TABLE / INOX TABLE / BANQUET TABLE

Friday, April 26, 2024

Item Name STAINLESS STEEL TABLE / INOX TABLE / BANQUET TABLE Model No QP-1644 Material 100% stainless steel Type of Stainless steel 201 High 75 cm Size of table tops + Round table: 80cm, 100cm, 120cm, 140cm + Rectangle table: 60x100cm, 70x 120/140/150/160cm...

Qui Phuc Company Limited

  • Luck06
  • 700000 - Ho Chi Minh
  • +84 9 86 58 28 62
France 529000 Equipment goods
2-Wire Flat Cool White LED Rope Light

Saturday, July 19, 2014

Cool White LED with color temperature 7000K to 7500K implies a mild blue tint in the white glow. Cool White is preferred in many applications because the light they output makes items illuminated appear crisper. Cool White is often preferred in bathrooms and other task areas. Note...

Real Green lighting Company

  • Bonny Chan
  • 529000 - Jiangmen City
  • +15 6 02 20 39 93