Digital Push Pull Force Gauge EFGE

With compact size, and high accuracy, the digital push pull force meter is easy to operate and handy to carry out. The digital push-pull force gauge, also called the digital push-pull force meter, can be widely applied in electron, high & low voltage electrical appliances, hardware, automobile parts, lighter and ignition system, light industry, mechanical, textile, and other industries for testing of pull or push load test, insertion force or pull and destructive experience.

EFGE digital push-pull force meters are high-precision push-pull force test instruments. The electronic push-pull force gauge adopts an aluminum alloy shell, and the whole machine is light in weight. It is especially suitable for hand-held measurement. It has built-in high-precision sensors and mechanical overload.

The internal sampling frequency of this digital pull force gauge is 1000HZ, the software has tracking, peak, and preset modes, which can be applied to the brake test of the product. Compared with the compression force gauge, the insertion force test and other force tests, up to 500 measurement data storage.

Digital Push Pull Force Gauge EFGE Features

Durable metal case

Reverse display setting

Mechanical overload protection

Calibration certificate Included

Charger with US/EUR/UK Plugs selectable

With the USB or RS232 communication interface, this digital push-pull gauge can easily communicate with PLC

Accuracy: ± 0.3% FS

Sampling Rate: 1KHz

Digital Push Pull Force Meter EFGE Specifications

How to Use Push-Pull gauge?

Choose model

This pull-push meter series has a variety of models can be selected. Different models corresponde to different range and resolution. Select the appropriate model based on practical needs before use. DO NOT exceed the capacity of the gauge, or it may damage the force gauge forever.

Choose measuring heads

In order to complete the test work conveniently, this pull force meter is equipped with a variety of measuring heads(adapters). Select the appropriate measuring heads according to the actual need.

Power on/off

Touch the power switch for 2 seconds to power it on or off.

After switching the instrument on, you should check the model and the battery Icon. If the power is low, the push-pull meter should be recharged.

Testing

After completion of the test preparation, testing can be done.

- Measuring heads

Select the appropriate measuring head, install it on the gauge's measurement axis. Tighten it by hand, without the use of tools. Do not use a deformed or damaged measuring head.

NOTE: Do not use tools to vigorously tighten the measuring head, otherwise it will damage the force gauge.

- Units

The digital push-pull force gauge has a variety of measurement units, select the appropriate unit of force. Under the measured interface, press the Menu key to enter the menu interface.

- Test Mode

This push-pull force gauge series has 3 kinds of measurement test modes can choose from. You can select a Measure Mode by touching the measuring interface, or changing it in the menus.

Track: The real-time measuring mode, under this mode, press the zero key the force gauge will be cleared (remove tare).

Peak: Peak readings will not change until a higher value is measured. Under this mode, touch the zero key the force gauge will update the display immediately.

Auto-Peak: In this mode, the digital push-pull gauge displays a peak value of force in a fixed duration. The duration time can be set in menus.

- Tolerance Limit

The tolerance limits can be set for GO/NG measurement also. See for detail. If you set the alarm on and a valid limit, The icon will be displayed for within limit, lower than lower limit, or exceeding the upper limit.

- Zeroing

Touch the zero key to clear the pull force meter in track mode for removing the tare.

Hand-held or Mounting

The digital push-pull gauge is a portable Instrument. You can do the testing hand-held, or you also can install the force gauge on the test stand so as to obtain accurate measurement results. There are 6 M4.0 mounting screw holes on the back, which can be fixed on the test stand.

NOTE: The depth of the mounting hole is 8.0mm, please choose the appropriate screws, screw into the depth of the force gauge shall not be greater than 7mm.

Storage

Measured results can be stored in the digital push pull gauge so that you can review or print them later. Under the measured interface, touch to save value measured, and the save icon will be displayed.

Browse and Printing

The values saved in memory can be reviewed in the Browse function. The data in memory can be printed into a report.

Push-Pull Gauge Calibration Procedure

Because of the sensor material performance or the influence of external factors, there may be errors in a certain range after a period of time use. As one of the leading measuring instruments manufacturers in China, Mikrometry suggests you should send the digital push-pull gauge to a specialized testing organization for calibration.

Whereas, if you have some standard force weights or the other standard load and some test stand, you may calibrate the push meter also.

Mount the push-pull meter.

Remove the tare by use of the zero key.

Enter the Calibration interface, Show the following.

Push-Pull Gauge Calibration Procedure

Load a standard force. Now the value in the standard input area is just equal to the current measured value. Wait a moment for the force stability.

Touch the zero key and peak key to input the standard force value.

Touch to enter the next calibration. Touch can interrupt the calibration. When the 5 times calibration had been finished or interrupted, a confirm window will pop up to ask for save or not save the calibration.

Touch the zero key or peak key to select, then press the menu key.

If "YES" is selected, "Calibrate complete!" is displayed.

NOTE:

① Set the unit of the force to the unit used in calibration previously.

② Ensure that the tare weight of the attachment has been removed before calibration.

③ You can do any point or points calibration from 1 to 5 point. We recommend 5 points calibration.

Push Pull Force Tester Gauge Digital Close-Ups

As one of measuring equipment manufacturers, we will do our best to meet all the needs of customers.

More types of digital hardness meter, please visit our website.