Automatic Wrinkle Recovery Tester
The main principle of the wrinkle recovery tester is to apply a predetermined pressure to the specimen under standard atmospheric conditions and to maintain the specified time. The overall structure of the instrument and the precise spiral column ensure that the loaded specimens produce a uniform deformation. After removing the sample from the instrument, re-adjust the sample under standard atmospheric conditions and allow it to recover for a certain period of time, and then compare the sample with the reference sample to assess the appearance of the sample.
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The wrinkle recovery test instrument detects the recovery of the specimen after a certain period of time under a load. It is suitable for any fiber pure or blended fabric test. Besides, it can not maintain the shape of stable materials under the characteristics of the conditions, such as the material which is soft, thin and easy to bend. We can evaluate its anti-crease performance through this device.
Technical Parameters
Standard weights（2000g、1000g、500kg、200kg）
Full set 5 inch x 3 inch (5 / set)
The rating card (optional)
Standards:
AATCC 128 Wrinkle recovery of fabrics: Appearance method
ISO 9867 Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 3061
ISO 9867 Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 3061
Accessories:
(1)First ,use the pressure sample device, three samples are tested continuously. The interval is about 1min;
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
Technical Parameters
| Items | Parameters< /span> |
| Sample size | 15cm×28cm(6×11inch) |
| Weights | 2000g，1000g，500kg，200kg Accumulate |
| Dimensions | 150×150×330mm(L×W×H)< /span> |
| Weight | 9.5kg(21lb) |
Full set 5 inch x 3 inch (5 / set)
The rating card (optional)
Location : No. 2578 Minhang District Gu Dai Road, Shanghai, 201199 Shanghai,
Contact : Sun Qin, +86 21 6780 0179
Contact : Sun Qin, +86 21 6780 0179
Good deal: buying from seller
Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
|
This page is about importers and exporters of Automatic Wrinkle Recovery Tester Search in a category : Equipment goods Search in a category : tester, automatic, wrinkle, recovery |
France 
528500 Health / Hygiene
528500 Health / HygieneReport abuse
Sunday, July 12, 2015
Quantity : 1 - Price : 2 000,00 €
Options: 1.imported 4 hole high speed air turbine hand piece 2.imported 4 hole low speed air turbine hand piece 3.Endoscope system 4.Ulerasonic scaler 5.curing light Location : Foshan City , 528500 Foshan , Contact : Nature Mai Mai , +15 0 19 61 17 04
France Skylight International Limited
- 528500 - Foshan
- +15 0 19 61 17 04
Turkey 
06370 Food
06370 FoodReport abuse
Sunday, March 15, 2015
TAYSAN MAKINA CO. SARL. Is a company that makes the production of types R fullyautomatic and manual machines for making hard sugar cubed Turkey and alsomachines to various food packaging and sugar cubes since ten years experience. With its quality and his professional crew gives...
Taysan Makina Ltd
- taysanmakina
- 06370 - Ankara
- 0090 312 396 01 09
- 0090 546 610 06 05
Hong Kong 
050000 Everything else / Bulk
050000 Everything else / BulkReport abuse
Tuesday, June 16, 2015
Quantity : 10000m2/we - Price : USD 80-90/m2
Woven Middle Speed Corrugator Belt Woven High Speed Corrugator Belt was developed to high speed running and rapid dying of the corrugat ed board.the structure and the quality of the belt facilitates steam evaporation from the paperboard .The surface of the belt is twill weave to...
Huatao Wire Belt Factory
- 050000 - shijiazhuang
- 86 311 80772027
