Raw materials

Silicone Rubber For Tyre Molding

Quantity : 2000kgs   Price : 11.3-16.3USD/kg

Description

HY- E series addition molding silicone is generally named two-components silicone

rubber, Part A and part B. It features an exceptional fluidity and good operability.

The mixing ratio is 1: 1 (10: 1),mainly be suitable for making molds application.

Typical Applications

HY- E series addition molding silicone could be mainly used for making concrete

stones, wax molds, PU molds, resin molds, gypsum casting, candle molding and

chocolate , candy and any other FDA food product mold making,prototyping etc.

HY-E620 Silicone Rubberishas been used for years to make tire pattern molds .


Characteristics

*low shrinkage (less than 0.1% )

*high tensile and tear strength with high copy times

*easy for operation (mixing ratio at 1: 1 /10: 1)

*very good flow and easy for pouring operation

*Fast and non-shrink cure at room temperature which can be accelerated considerably by the application of heat

Technical Parameters

Product

E-620

Appearance

Translucent

Hardness(shore A)

20±2

Mix ratio(A: B)

1: 1/10: 1

Viscocity Part A(mPa.s)

23000±2000

Viscocity Part B(mPa.s)

3500±500

Tensile strength (kgf/cm2)

45±5

Tear-strength (kN/m)

20±2

Elongation(%)

500±50

Pot life/working time (mins)

30-40

Curing time/setting time (hrs)

3-4hrs(25℃)

110-20mins(60℃)

Shrinkage rate (%)

0.1

(Please note: the above data for this product in 25℃temperature, 55percent humidity conditions, for reference. The accurate data is measured by customers when using.)

Operation instruction of HY-E Series molding silicone:

1. Pls clear the model and tool totally before operation to prevent cure inhibition.

2.Weigh the two part correctly by electronic weight in two separate container .

3. Mixing the two part in 1: 1/10: 1 and stir part A and part B evenly in 2-3 minutes .

4.And get the mixture for vacuum-pumping for de-air the bubble in around 2-3

minutes . (If there is no vacuum machine, pls pour the mixture carefully and slowly

down the side of the mold frame so that less bubbles caused)

5. Enclose the product (the original model) with four plastic plates or wooden plates.

6. Clean your products and brush a layer of release agent(detergent or soap water) on

your product.

7. Pour the vacuumed mixture into the model frame from the side of the mold frame .

Notice:

As our E-series silicone is platinum cure silicone , which is very easy to cause

cure inhibition , so pls do remember thoroughly clean the model and tool before

operation . Besides , pls avoid the liquid E-series silicone contact or mix with the

following material , otherwise the silicone won't be cured :

1. Liquid condensation silicone ( condensation silicone not completely cured or organic

tin compounds )

2 .Sulphur, sulfide and sulfur rubber materials.

3. Amine compounds as well as contains the amine materials.

4 .Pewter solder flux.

SHELF LIFE:

8-10 months when stored under 24℃ in original unopened packages

PACKAGE:

If ratio is 1: 1 : Packed in 20kg/pail + 20kg/pail and 200kg/pail + 200kg/pail.

If ratio is 10: 1 : Packed in 20kg/pail + 2kg/pail and 200kg/pail + 20kg/pail.

Location : Building 4,No.6 Laiying road ,Xin Sheng Long Shan Industrial Zone,Long Gang District,Shenzhen, 518117 Shenzhen,
Contact : Bella Wong, 0086 755 89212380

Good deal: buying from seller

Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of
Silicone Rubber For Tyre Molding

Search in a category : Raw materials
Search in a category :
rubber, molding, tyre, silicone
Toshiba 3.5inch - 8000 Go - 7200 tr/min MG06ACA800E

Wednesday, June 22, 2022

Quantity : 100

Toshiba MG06ACA800E. Taille du disque dur: 3.5", Capacité disque dur: 8000 Go, Vitesse de rotation du disque dur: 7200 tr/min Caractéristiques Taille du disque dur 3.5 " Capacité disque dur 8000 Go Vitesse de rotation du disque dur 7200 tr/min Interface SATA Type Disque dur Taille...

MaKant Europe GmbH & Co. KG

  • 60386 - Frankfurt am Main
  • +49 (69) 9 150 750 14
Germany 60386 Audio and Video
Duracell Batterie Lithium Knopfzelle CR2025 3V Blister (2-Pack) 203907

Saturday, June 25, 2022

Quantity : 100

Les piles boutons au lithium Duracell format 2025 sont fabriquées à base de lithium de haute qualité apportant +50% de longévité* à vos appareils (* par rapport à la durée moyenne minimum des tests standard IEC des piles boutons au lithium 2025. Les résultats peuvent varier suivant...)

MaKant Europe GmbH & Co. KG

  • 60386 - Frankfurt am Main
  • +49 (69) 9 150 750 14
Toshiba Disque dur interne X300 Performance 8TB 3.5" HDWR180UZSVA

Wednesday, June 22, 2022

Quantity : 100

Toshiba X300. Taille du disque dur: 3.5", Capacité disque dur: 8000 Go, Vitesse de rotation du disque dur: 7200 tr/min Caractéristiques Taille du disque dur 3.5 " Capacité disque dur 8000 Go Vitesse de rotation du disque dur 7200 tr/min Interface Série ATA III Type Disque dur composant...

MaKant Europe GmbH & Co. KG

  • 60386 - Frankfurt am Main
  • +49 (69) 9 150 750 14