Factory Price Good Quality RTV2 Moldmaking Tin Liquid Cured Silicone Rubber LSR Raw Mat...
Quantity : 500ton Price : $4.5/kg
Product Description
Specification
Condensation Cured Silicone Rubber for Mold Making, which is also named condensed cure silicone rubber and Tin cure silicone rubber, is
generally industrial liquid silicone rubber vulcanized under room temperature(RTV-2).
Applications
Condensation Cured Silicone Rubber has extensive use,such as mold making of gypsum,plaster,concrete,cement,flowerpot,candle,soap,resin
crafts,cultural stone,sculpture,GRC/GRG restoration and so on.
Techinical Parameters
Model Code | GTSIL-T10 | GTSIL-T15 | GTSIL-T20 | GTSIL-T25 | GTSIL-T30 | GTSIL-T40 |
Hardness - Shore A | 8-10 | 14-16 | 19-21 | 24-26 | 28-32 | 38-40 |
Viscosity - Cps | 10000-14000 | 12000-16000 | 14000-18000 | 16000-20000 | 26000-32000 | 10000-14000 |
Mixing Ratio - % | 3% | 3% | 3% | 3% | 3% | 3% |
Tear Strength - KN/m2 | 10-15 | 15-18 | 19-23 | 23-27 | 25-30 | 16-20 |
Tensile Strength - Mpa | 3.5-5.5 | 3.5-5.5 | 4-6 | 4-6 | 5-7 | 3.5-5.5 |
Shrinkage - % | 0.30% | 0.30% | 0.30% | 0.30% | 0.30% | 0.30% |
Elongation - % | 400-500% | 400-500% | 400-500% | 400-500% | 350-500% | 350-500% |
How to use
1.Substrate Preparation
The surface of the original should be clean and free of loose material. If necessary, and in particular with porous substrates, use a suitable release agent such as petroleum jelly or soap solution.
2. Mixing
Thoroughly stir Part A (silicone base) before use as filler separation may occur upon prolonged storage.
Weigh 100 grams Part A (silicone base) and 3 grams Part B (curing agent) in a clean container. Mix together until the curing agent is completely dispersed in the base. Hand or mechanical mixing can be used, but do not mix for an extended period of time or allow the temperature to exceed 35°C (95°F). Mix suitably small quantities to ensure thorough mixing of the par A (silicone base) and part B (curing agent).
It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mix to completely expand and then collapse. After a further 1-2 minutes under vacuum, the mix should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture, so a suitably large container should be chosen.
Caution: prolonged vacuum will remove volatile components from the mix and may result in poor thick section cure and non-typical properties.
Note: If no vacuum de-airing equipment is available, air entrapment can be minimized by mixing a small quantity of par A (silicone base) and part B (curing agent), then using a brush, painting the original with a 1-2mm layer. Leave at room temperature until the surface is bubble free and the layer has begun to cure. Mix a further quantity of base and curing agent and proceed as follows to produce a final mold.
3. Pouring the Mixture and Curing
Pour the mixed Par A (silicone base) and Part B (curing agent) as soon as possible onto the original, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 24 hours at room temperature (22°C-24°C/ 71.6°F - 75.2°F) and the mold can then be separated from the original. If the working temperature is significantly lower, the cure time will be longer. If the room temperature or humidity is very high, the working time of the catalyzed mixture will be reduced. The final mechanical properties of the mold will be reached within 7 days.
Contact : Chis Wong, 86076982806708
Good deal: buying from seller
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of Factory Price Good Quality RTV2 Moldmaking Tin Liquid Cured Silicone Rubber LSR Raw Mat... Search in a category : Raw materials Search in a category : moldmaking, good, factory, rtv2, price, quality, liquid |
Thursday, May 02, 2024
Quantity : 20 Unit - Price : $836
Price: US $836 Site: azriadi.com Accept paypal The SP31 included an improvement to the ASICs that delivered more hashing for the same power consumption. With the SP35 we replaced the PSUs to squeeze out even more out of the RockerBox ASICs. This new design will deliver 5.5TH/s...
Friday, June 17, 2016
COCOA GRADE I High quality Cocoa beans producing beans with the strongest flavour Raw Sun-dried Cocoa Beans A) Moisture: 5.5% - 6.2% maximum b) Foreign Matters: 1.29% maximum c) Beans count: 91 to 99 beans/kg d) Broken beans / Defective: 0.7% - 0.8% maximum Location : Rue bebey eydi...
STE JASTCOOP
- 00237 - Douala
- 33242233
Sunday, December 13, 2015
Hello sır, · Golden cake gıda San. A.Ş. is founded On March 29, 2015 in Konya. Our company in a closed area of 3200 m2 product a many kind of cakes. Golden cakes always taking care of the hygiene and the environment to produce with high quality, our usual raw material is always...
zanon gida import export
- 421000 - konya
- 00905536336580