Raw materials
Factory Price Good Quality RTV2 Moldmaking Tin Liquid Cured Silicone Rubber LSR Raw Mat... |
Model Code | GTSIL-T10 | GTSIL-T15 | GTSIL-T20 | GTSIL-T25 | GTSIL-T30 | GTSIL-T40 |
Hardness - Shore A | 8-10 | 14-16 | 19-21 | 24-26 | 28-32 | 38-40 |
Viscosity - Cps | 10000-14000 | 12000-16000 | 14000-18000 | 16000-20000 | 26000-32000 | 10000-14000 |
Mixing Ratio - % | 3% | 3% | 3% | 3% | 3% | 3% |
Tear Strength - KN/m2 | 10-15 | 15-18 | 19-23 | 23-27 | 25-30 | 16-20 |
Tensile Strength - Mpa | 3.5-5.5 | 3.5-5.5 | 4-6 | 4-6 | 5-7 | 3.5-5.5 |
Shrinkage - % | 0.30% | 0.30% | 0.30% | 0.30% | 0.30% | 0.30% |
Elongation - % | 400-500% | 400-500% | 400-500% | 400-500% | 350-500% | 350-500% |
How to use
1.Substrate Preparation
The surface of the original should be clean and free of loose material. If necessary, and in particular with porous substrates, use a suitable release agent such as petroleum jelly or soap solution.
2. Mixing
Thoroughly stir Part A (silicone base) before use as filler separation may occur upon prolonged storage.
Weigh 100 grams Part A (silicone base) and 3 grams Part B (curing agent) in a clean container. Mix together until the curing agent is completely dispersed in the base. Hand or mechanical mixing can be used, but do not mix for an extended period of time or allow the temperature to exceed 35°C (95°F). Mix suitably small quantities to ensure thorough mixing of the par A (silicone base) and part B (curing agent).
It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mix to completely expand and then collapse. After a further 1-2 minutes under vacuum, the mix should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture, so a suitably large container should be chosen.
Caution: prolonged vacuum will remove volatile components from the mix and may result in poor thick section cure and non-typical properties.
Note: If no vacuum de-airing equipment is available, air entrapment can be minimized by mixing a small quantity of par A (silicone base) and part B (curing agent), then using a brush, painting the original with a 1-2mm layer. Leave at room temperature until the surface is bubble free and the layer has begun to cure. Mix a further quantity of base and curing agent and proceed as follows to produce a final mold.
3. Pouring the Mixture and Curing
Pour the mixed Par A (silicone base) and Part B (curing agent) as soon as possible onto the original, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 24 hours at room temperature (22°C-24°C/ 71.6°F - 75.2°F) and the mold can then be separated from the original. If the working temperature is significantly lower, the cure time will be longer. If the room temperature or humidity is very high, the working time of the catalyzed mixture will be reduced. The final mechanical properties of the mold will be reached within 7 days.
Good deal: buying from seller
This page is about importers and exporters of Factory Price Good Quality RTV2 Moldmaking Tin Liquid Cured Silicone Rubber LSR Raw Mat... Search in a category : Raw materials Search in a category : moldmaking, factory, price, liquid, rtv2, good, quality |
Friday, May 10, 2024
lighting fixtures
Quantity : 14000 - Price : 2,00 €
Take advantage of our special offer exclusively for B2B clients: an impressive lot of 14,000 lighting fixtures, varied in design and functionality, offered at the exceptional price of only €2 per piece. Offer Details: - Quantity Available: 14,000 pieces - Price Per Unit: €2 - Variety: Multiple models available, suited to different uses and aesthetic preferences. Products Available: - Modern indoor lighting fixtures - Outdoor and garden lamps - Economical and durable LED lighting...
Monday, November 26, 2012
Quantity : 10
Pharma Clean Room Furniture Neptune Industry is reputed name in Pharma Clean Room Furniture manufacturer, supplier and exporter in India and overseas market. Our Pharma Clean Room Furniture is available in wide range and any design and shape. Our experts are able to manufacture high...
Monday, November 10, 2014
Quantity : 3500-4000 - Price : 6-10
21 shirts / T-shirts / jackets / pulls / Cardigans 21 shirts / T-shirts / jackets / pulls / Cardigans Pima cotton PSI Report and photos on demand Location : route d'arlon206-210, 8040 Strassen, Contact : raphael orsini, 00352661878746