GK1720A Pendulum Grinding Mill
GK1720A Grinding Mill is designed by our technicians based on GK1720 mill.This is a large type mill with optimized design.
Technical & Structural Benefits of roller ball mill:
Optimized shock-absorption design for the main unit, reduce vibration when the mill running.
Optimized design for the main unit structure, improve overall strength and rigidity.
The innovative design of the "maintenance-free device" for grinding roller assembly, Refill grease every 30 days.
Optimize inside design of the main unit, keep the roller and grinding ring abutting contact during running, improve grinding efficiency and operational reliability, and reduce the high failure rate of vertical pendulum grinding mill.
Equipped with water cooling structure for reducer of the main unit. Reducer adopts German technology.
Automatic control for air blower valve, reduce operating labor intensity。
Integral installation of air blower; water cooling system ensures running efficiency.
Running more smoothly, High capacity, low noise, energy saving.
Intelligent control. The one button start and stop system and fault alarm system reduce operating personnel.
Model |
Max Feeding Size |
Product Fineness (mash) |
Capacity |
Gross Weight |
Total Installed Power |
GK2500 |
≤35mm |
80-325mesh |
15000-50000kg/h |
66t |
625kw |
GK2150 |
≤35mm |
80-325mesh |
10000-40000kg/h |
64t |
548kw |
GK1720A |
≤35mm |
80-325mesh |
6000-25000kg/h |
49t |
424.5kw |
GK1620A |
≤30mm |
80-325mesh |
3000-18000kg/h |
34.5t |
329.5kw |
GK1500 |
≤20mm |
80-325mesh |
2500-16000kg/h |
31t |
242kw |
5R4128 |
≤20mm |
80-325mesh |
2000-14000kg/h |
28.5t |
220kw |
5R4125 |
≤20mm |
80-325mesh |
2000-14000kg/h |
28.5 |
202kw |
GK1280 |
≤20mm |
80-325mesh |
1500-10000kg/h |
19t |
133.5kw |
4R3220 |
≤20mm |
80-325mesh |
1000-7000kg/h |
14.6t |
101.5kw |
Preparation before operation of GK1720A Pendulum Grinding Mill:
Check that the supply voltage meets corresponding requirements. Don't start the machine when the voltage is lower than 360 v. Check the electric circuit in the light of drawing.
Check all joint bolts for tightness, especially the bolts in host chamber.
Check drive belt for looseness and tightness. The mainframe can rotate freely by moving it with hands. Check grinding rollers for flexible movement. The buffer spring above the roller assembly in the main unit should be screwed up to 185mm(see drawing 2); the length of four spring should be kept on the same size.
See that governor valve of inlet pipe air blower is in "off" position(it is automatically controlled by the pneumatic valve. Before start the blower, power on it to test it first. Normally the positioning pin is fixed to the positioning hole. After electromagnetic switch valve is energized, under the effect of air pressure, the cylinder activities section stretches out and drive the connecting rod, then the valve plate is open. When it is powered off, the valve is closed.)( see drawing 4)
Check the chain of the elevator for looseness and tightness.
Lubricate all parts according to the lubrication table. Lubricants are filled before use.The grease is clean. Check all the joints for oil leakage.
Regulate the discharge opening of jaw crusher in line with the nature of materials. The particle size is less than 35 mm.
Check motors for rotating direction.
a. The main engine has a clockwise running (looking down from above).
b. The turbine blade of the separator has a clockwise running(looking down from above).
c. The air blower rotates clockwise(looking from belt wheel end).
Check pulse dust collector:
Start induced draft fan. Check shell and discharge valve for air leakage.
Keep the pressure of air compressor piping system on 0.5-0.7 MPa. Check
Contact : Zeng Ralap , 0773 6812095
Good deal: buying from seller
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of GK1720A Pendulum Grinding Mill Search in a category : B2B Services Search in a category : mill, gk1720a, grinding, pendulum |
Wednesday, April 22, 2015
Quantity : 10PCS - Price : USD3250
Power: 150W Meanwell HLG series power drive+ original LED brigelux 45 mm Five years of protection We can also supply 150W 200W 80W 60W 30W Lighting: the angle of 90 degrees Input voltage: AC100 - 277v LED brightness attenuation: < 5% / 6000 hours PF>0.96 Work life: 50000...
Ashiloy Industry Co.,Ltd
- 999077 - KLN
- +86 138235618632
Friday, September 09, 2016
Quantity : 400 - Price : 8,00 €
Déstokage 400 smoke detectors EI ELECTRONICS EI650 manufactured in Europe with an autonomous lithium battery in until 2026 (20 cartons of 20 detectors with wall mounting screws and operating instructions in French). TECHNICAL CHARACTERISTICS - Test button and break against false...
DOMERCA
- 69100 - VILLEURBANNE
- 06 25 41 37 41
Monday, March 04, 2013
Quantity : 30 - Price : $395.00
It's not just phone we're talking about... it's smart phone... it's Samsung GALAXY S III. It has the looks and a symmetry which would make you proud to hold it in your hands. You couldn't ask for more imposing façade than its 4.8 inches HD Super AMOLED high-definition display. It delivers...