China Craft
Craft

Auto Bumper Mould


The front and rear bumpers of the car are made of plastic, which not only maintains the protection function, but also has the characteristics of harmony and unity with the body shape, lightweight, and low fuel consumption. The plastic front bumper consists of three parts, namely the outer panel, the buffer material, and the cross member. The raw materials of the outer plate and the buffer material are all plastic, the beam is stamped into a U-shaped groove from a cold-rolled sheet, and the thickness of the cold-rolled sheet is about 1.5 mm. There are generally two types of materials used in bumper mold : polyester and polypropylene, and the molding process is generally injection molding.

Automobile Bumper Mold Manufacturing

Green Vitality is a professional automobile mold manufacturer and has rich experience in automobile bumper mold manufacturing.

The car bumper injection moulding designed by Green Vitality not only has the ability to reduce the injury of drivers and passengers during high-speed impact but also has the ability to protect pedestrians. Green Vitality uses an internal parting structure design for the bumper mold. Compared with the traditional outer parting structure design, the inner parting design has higher requirements on the strength of the mold. Correspondingly, the design concept of the bumper mold made by the internal parting structure is more advanced.

Basic Information for Auto Bumper Mould

Auto Bumper Mould Specification

Description

Auto Bumper Mold

Plastic material

PP

Mould cavity&core steel

P20,2738,718H,738H,NAK80,SKD61,E420,etc.

Mould weight (T)

10T

Feeding System

Cold runner/ Hot runner

Hot runner brand

YUDO, HUSKYFISA, HASCO, MOLD-MASTER

Nos of Cavity

1*1

Manufacture time (day)

120 days

Mould life

≥500000

Packing

Vacuum+plywood wooden box

Green Vitality Can Offer You with Auto Bumper Mould

Analysis: Through the analysis of material properties and product feasibility, such as wall thickness, deformation, plastic feeding position, etc., potential problems can be predicted in advance.

Communication: Maintain close communication with customers, and understand the functional requirements and precautions of products from the perspective of customers, such as requirements for weld lines, requirements for appearance, etc.

Design: Strict design review system and checklist check. Before design, during the design of the scheme structure discussion meeting, the designer will check himself according to the checklist; after design, review together with the manufacturing department.

Quality inspection: Quality inspection of each link to discover mass production problems in advance.

Project management: Each project is equipped with a project manager, who strictly follows the schedule to control the project cycle, and provides weekly progress reports and mold photos for each project so that customers can keep abreast of the status.

Service: From mold design to continuous mass production of products, we provide full life cycle service support.

After-sales service: continuous after-sales follow-up service, proactively providing mass production and processing technical consulting services.

Technical support: In the mass production process, if there is any problem with the mold, technical support will be provided unconditionally.

Why Are Auto Bumpers Made of Plastic Material?

Control costs

The bumper steel plate is replaced with plastic, the cost is greatly reduced, the production is convenient, and the plastic bumper is also very malleable, which can meet the bumper design requirements of various car models.

Realize lightweight

If a car is too heavy, it will greatly increase the fuel consumption requirements, and the increased emission pollution is not good for the environment. Nowadays, the emission of vehicle exhaust is becoming more and more stringent. From the root of the car, the weight of the body must be reduced. This is the development of the car. The trend is also to design plastic for fuel economy and environmental protection. The use of plastic bumpers will not only reduce fuel consumption but also improve performance.

Protect pedestrians

The plastic bar material is elastic and has better shock absorption and buffering capacity than steel plates. If it is still a steel plate, if you hit someone, the consequences will be serious. Then there is no need to go to the hospital, just go to the crematorium, and the design is made of plastic It can greatly reduce the damage caused by impact.

Anti-corrosion

Plastics have inherent advantages over metals. Metals are prone to rust and corrosion when exposed to water and air, which affects the appearance of cars. Plastics have good corrosion resistance, so there is no need to worry about rust.

With self-repair function

Usually, the bumper made of plastic material has little effect when driving. It has elasticity and can repair itself, leaving only a few small scratches. As shown in the figure, it may be restored to its original state once it is heated with hot water. Otherwise, the pits created by the impact cannot bounce by themselves and affect the appearance.

As a plastic injection factory, we can offer kinds of plastic injection mold for sale, anything you need, please leave us a message.

Location : 101#, Building C, North Yongfa Hi-Tech Industrial Park, Shajing Road, Shajing Town, Bao'an District, Shenzhen, China, 518104 Shenzhen,
Contact : Qin Susan , 0755 26825352

Good deal: buying from seller

Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute.
We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
This page is about importers and exporters of
Auto Bumper Mould

Search in a category : Craft
Search in a category :
auto, mould, bumper
GOLD ad
France 22440 Stock lots
Lot of 1000 American Samsung RS68CG882ES9 Refrigerators at Clearance Price!
Verified

Tuesday, December 24, 2024

American Samsung Refrigerators

Quantity : 1000 - Price : 590,00 €

Exclusive Offer: Lot of 1000 American Samsung RS68CG882ES9 Refrigerators at Clearance Price! Seize this unique opportunity with a lot of 1000 American Samsung RS 68 CG 88 2E S9 refrigerators at an exceptional clearance price of €590 per unit. This high-end model is perfect for wholesalers looking to offer their customers a product that combines elegant design, advanced technology, and energy efficiency. Key features of the Samsung RS 68 CG 88 2E S9: - Large storage capacity ...

TRANSIDI

  • 22440 - PLOUFRAGAN
  • 02 30 96 63 26
  • 33(0)603670505
Switzerland Audio and Video
IPhone 5C Hülle Schutzhülle Handyhülle Silikon Rückcover Hülle

Saturday, November 01, 2014

Schutzhülle Case Cover für iPhone 5C iPhone 5C Silikon Rückcover Hülle Rückcover Case Silikon Rücketui mit Standfunktion Schwarz Schutztasche Case Cover mit Halter Rückcover f. iPhone 5C Die Schutzhülle kann nicht nur Ihr Handy verschönen, sondern auch vor Kratzern und Stauben schützen...

Euro-Sino

  • - Thun
Switzerland 3600 Stock lots
Kurbelabzieher kaufen Tretkurbel kaufen Kurbelabnehmer

Monday, September 29, 2014

Vorteil: Unser brandneue und hochwertige Produkt ist ideal zur Demontage am Fahraad. Es wird von hochwertigem Metall hergestellt und fein verarbeitet. Deshalb ist es robust und strapazierfähig. Das handliche Design macht Ihre Verwendung bequem. Es ist ganz praktisch in Ihrer Fahraad...

365buy

  • 3600 - Thun
  • 07 62 07 63 81