Electronics / Computers
China Manufacturer Mosi2 Heating Elements
|
Volume Density |
Bending Strength |
Vickers Hardness |
Porosity |
Water absorption |
Heating Elongation Rate |
5.5g/cm3 |
15-25kg/cm2 |
(HV)570kg/mm2 |
7.4% |
1.2% |
4% |
2. Chemistry Property
Mosi2 heating element is used in the high temperature under oxidizing atmosphere. It will form the SiO2 film which can keep the element from being melted. When the temperature of element is more than 1700 °C, the SiO2 protecting film is formed again when the element continues to be used. The Mosi2 heating element must not be used in the temperature between 400°C and 700°C, otherwise the element will be creamed under the strong oxidizing function in the low temperature.
3. The using temperature under the different atmosphere
Atmosphere |
The Maximum Using Temperature of Element |
|
1700 Grade |
1800 Grade |
|
NO2,Co2,O2,Air |
1700°C |
1800°C |
He, Ar , Ne |
1650°C |
1750°C |
SO2 |
1600°C |
1700°C |
CO,H2 |
1500°C |
1600°C |
Wet H2 |
1400°C |
1500°C |
Dry H2 |
1350°C |
1450°C |
Advice of Installation
1. MoSi2 heating element is very brittle under room temperature and plastic under high temperature. Therefore, it's the best way for installation of U type element to hang it vertically. Such way is to avoid putting the mechanical stress directly to the Hot Zone of the element, otherwise, the element will be broken easily. If it needs hang horizontally, please choose a support of high temperature refractory.
2. Please put the taper part of the element bottom into the furnace chamber to avoid local overheating.
3. The lead wire should be a little longer than the linear distance between the element and the bus to avoid putting the stress to the element.
4. Please don't tighten the screw of clamps too much at one time. It can be tightened when the element heats up to high temperature because of the element's plasticity.
5. The temperature of the clip should be less than 200°C, the contact voltage between the clip and the element should be less than 0.1V.
6. The distance between the lower end of the clip and the upper surface of the through brick should be more than 50mm, to avoid the radiation heat conducting to the clip.
7. To avoid damage, 170A couldn't be used for long term for the element of Ø6/12mm; 300A couldn't be used for long time used for the element of Ø9/18mm.
Package and shipping
1.Package
First carton packaging with plastic inside to protect, then wooden packaging outside;
For some special conditions, use iron hanger outside wooden case.
2. Shipping
Fedex/DHL/UPS/TNT for samples, Door-to-Door;
By Air or by Sea for batch goods;
Customers specifying freight forwarders or negotiable shipping methods;
Delivery Time: 3-7 days for samples; 5-25 days for batch goods.
When you enquiry, please tell us the following data:
DI: Diameter of Hot Zone(mm)
D2: Diameter of Cold Zone(mm)
Le: Length of Hot Zone(mm)
Lu: Length of Cold Zone(mm)
A: Shank Spacing(mm)
Good deal: buying from seller
This page is about importers and exporters of China Manufacturer Mosi2 Heating Elements Search in a category : Electronics / Computers Search in a category : china, elements, mosi2, heating, manufacturer |
Friday, May 04, 2012
Quantity : 1000 and m - Price : $2,95
We sell High Power Led Products, Led panels, Led Bulbs, Led Spotlights, Led Downlights etc,etcLocation : Kaja de Ojeda 13, Curacao, Contact : Melvin Torres, +19 1 72 67 86 70
Thursday, August 23, 2007
Quantity : 1000 - Price : 3 150,00 €
We have been enjoying a great reputation for providing consistently high quality and original brand new in box of projector, competitive price, and comprehensive service. Full service include delivery, setup, strike, and return services, providing our clients with an absolutely worry...
Thursday, January 11, 2007
we are manufacturere of all kind of railway track fittings and fastners. we also produce other high tension fasteners and supply them glopbally. we are also regularly supplying electrical overhead line hardwares. We can produce them as per buyer drawing and specification.Location ...