Raw materials
ASTM A335 P92 High pressure boiler pipes
Quantity : 1000 Price : 1 000,00 €
ASME SA335 P92,ASTM A335,ASTM A335 P92,High pressure boiler pipes
ASTM A335 P92 is the part of ASTM A335, The pipe shall be suitable for bending, flanging, and similar forming operations, and for fusion welding. The steel material shall conform to chemical composition, tensile property, and hardness requirements.
ASTM A335 P92 alloy steel pipe
ASTM A335 P92 high pressure semaless boiler pipe, The range of ASTM A335 P92 seamless alloy steel pipe sizes that may be examined by each method shall be subjected to the limitations in the scope of the respective practice.
Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices.
The range of ASTM A335 P92 pipe sizes that may be examined by each method shall be subjected to the limitations in the scope of the respective practice.
The different mechanical test requirements for pipes, namely, transverse or longitudinal tension test, flattening test, and hardness or bend test are presented.Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.
-
Outer Dimensions: 19.05mm - 114.3mm
-
Wall Thickness: 2.0mm-14 mm
-
Length: max 16000mm
Steel grade: ASTM A335 P92
Packing:
Bare packing/bundle packing/crate packing/wooden protection at the both sides of tubes and suitably protected for sea-worthly delivery or as requested.
Inspection and Test:
Chemical Composition Inspection, Mechanical Properties Test(Tensile Strength,Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test), Surface and Dimension Test,No-destructive Test, Hydrostatic Test.
Surface treatment:
Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.
Chemical Requirements of ASTM A335 P92
UNS Designation |
K92460 |
Carbon |
0.07–0.13 |
Manganese |
0.30–0.60 |
Phosphorus(max) |
0.02 |
Sulfur(max) |
0.01 |
Silicon |
0.50 max |
Chromium |
8.50–9.50 |
Molybdenum |
0.30–0.60 |
V |
0.15-0.25 |
N |
0.03-0.07 |
Ni (max) |
0.4 |
Al(max) |
0.02 |
Cb |
0.04-0.09 |
W |
1.5-2.00 |
B |
0.001-0.006 |
Ti (max) |
0.01 |
Zr(max) |
0.01 |
Mechanical Properties of ASTM A335 P92
Properties |
Data |
Tensile strength, min, (MPa) |
620 |
Yield strength, min, (MPa) |
440 |
Elongation, min, (%), L/T |
20/… |
Material & Manufacture
Pipe may be either hot finished or cold drawn with the finishing heat treatment noted below.
Heat Treatment
Mechanical Tests Specified
-
Transverse or Longitudinal Tension Test and Flattening Test, Hardness Test, or Bend Test
-
For material heat treated in a batch-type furnace, tests shall be made on 5% of the pipe from each treated lot. For small lots, at least one pipe shall be tested.
-
For material heat treated by the continuous process, tests shall be made on a sufficient number of pipe to constitute 5% of the lot, but in no case less than 2 pipe.
Notes for Bend Test:
-
For pipe whose diameter exceeds NPS 25 and whose diameter to wall thickness ratio is 7.0 or less shall be subjected to the bend test instead of the flattening test.
-
Other pipe whose diameter equals or exceeds NPS 10 may be given the bend test in place of the flattening test subject to the approval of the purchaser.
-
The bend test specimens shall be bent at room temperature through 180 without cracking on the outside of the bent portion.
Location : Carretera Siping, Shanghai, 200081, China, Shanghai 闸北, Contact : Sum Xuu, 862133780199
Registered since 22 September 2013
Good deal: buying from seller
Visit our guide for a secure transaction! Under no circumstances Algomtl can be held responsible for the content of the ads published. Only the sellers and buyers responsability is involved in case of dispute. We invite you to read our terms of use. You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
Wednesday, December 14, 2022
Price : USD 0.65 / Ream
SPECIFICATION Brand: Double A (Original) Size: A4 (210mm x 297mm), Legal (Legal 216mm × 356mm), Letter (216mm × 279mm) Substance: 80gsm,75gsm,70gsm Brightness: 102-104% above Color: white Whiteness: CIE167 Grade: All purpose Premium Paper Sheet in Ream: 500 Roughness: 140ml/Min Ream box...
- 29422 - Batam
- +627787062288
Tuesday, January 08, 2019
- Automatic Carton Box Print & Gluing Machine - Shanghai Jinchang Carton Machinery Manufacture Co., Ltd is a famous China carton gluing machine Manufacturers and Box Gluing Machinery suppliers,our company was founded in 2000.It covers an area of nearly 20,000 square meters, among which...
- 345100 - Shanghai
- 0086 021 31766187
Tuesday, June 06, 2017
one of our clients "The Egyptian Group for export" located in Behira,Egypt. we are an exporter of Green peas. Tomatoes specifications: Summer lug early: It is grown from late January to early March, according to the weather conditions of varieties Super styrene me, Beto 86, Yossi...
- 045 - Damanhour
- +20 4 53 33 18 99
|